BP4CH12V5A 4CH BALUN HUB W/ BUILT IN 12VDC/5A POWER SUPPLY AND 4X VPB45 BALUNS
With the same features and abilities as the DOSS Video+Power baluns, and the convenience of a single box withbuilt-in power supply, the BP4CH12V5A is able to supply 4x CCTV cameras with 12VDC, up to 1A each. Video received from the transmitting baluns is output via 4x Female BNC connections straight into your DVR or other recording device.
Features 4x 8P8C (RJ45) connections for UTP cable, enabling quick and simple installation. Working with the DOSS Passive Video+Power Baluns (included), the BP4CH12V5A eliminates costly and bulky coaxial cable, allowing live CCTV colour video signal transmission up to 400m (1300ft).
The superior interference rejection and low emissions ofthe BP4CH12V5A allow signals to coexist in the same wire bundle as telephone, datacom, or low-voltage power circuits.This allows the use of a shared or existing cable infrastructure. The BP4CH12V5A has built-in surge suppression to protect video equipment against damaging voltage spikes. Its crosstalk and noise immunity ensure quality video signals.
4-8 cameras connected to DVR via powered hub
Many cameras to DVR via powered hub w/ long runs.
The DOSS Range of UTP Video+Power Baluns allow you to connect your CCTV system using cheaper, thinner, lighter andmore readily available CAT5E cable rather than expensive andbulky RG59U cable.
The passive (non-amplified) baluns allow transmission of realtime CCTV video signals and power over cost-effective Unshielded Twisted Pair (UTP) cable, without any compression, loss or signal degradation and without the needfor extra power supplied to be installed. Sending camera power over the same twisted pair as video means less cabling, and no power supply required to be installed near to the camera. Baseband (composite) signals of any type are supported.
Applied Devices | CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equipment | |
Video | Video Format | PAL, NTSC, SECAM |
Operating Frequency | DC to 5MHz | |
Max Distance | UTP Category 5e (24AWG) Colour: 400m (1300ft)_ B&W: 600m (1950ft) | |
Common-mode / Differential-mode rejection | 15kHz to 5MHz 60dB typical | |
Impedance | Coax, Male BNC 75O unbalanced | |
UTP, two coax pigtail 100O balanced | ||
Attenuation | 1.5dB Max typical | |
Wire Type | Network Wiring | One Unshielded Twisted Pair (for eachvideo signal) 24-16 AWG (0.5-1.31mm) |
Category Type | 2 or better | |
Impedance | 100 20 ohms | |
DC Loop Resistance | 18O per 100m (52O per 1,000ft) | |
Differential Capacitance | 62 pF/m max (19 pF/ft max) | |
Power | No external power required to operate | |
Power input/output | Input: 176~264VAC 50Hz / 90~130VAC60Hz | |
Connector | Video input/output | 4x Female BNC connector |
Video input/output | 1x 8P8C (RJ45) Video (4-in-1) | |
Balun input | 4x 8P8C (RJ45) Video+Power | |
Protection | Surge Protection | Built-in Transient Voltage Suppressor(TVS) |
Antistatic | Yes | |
Mechanical | Housing | Metal |
Body Colour | Black | |
Dimensions (L*W*H) | mm | |
Net Weight | _ | |
Environmental | Operating Temperature | -20°~ 70°C |
Relative Humidity | 0~95% (non-condensing) | |
Storage Temperature | -40°~ 150°C |
_ | |
_ | |
Power indicator—power is being transmitted/received | |
Over-current—maximum current (1.5A) has been exceeded |
_
DOSS Video & Power Baluns | T568A | T568B | |
---|---|---|---|
Pin 1 | Video | White/Green | White/Orange |
Pin 2 | Video | Green | Orange |
Pin 3 | Power_ | White/Orange | White/Green |
Pin 4 | Power_ | Blue | Blue |
Pin 5 | Power_ | White/Blue | White/Blue |
Pin 6 | Power_+ | Orange | Green |
Pin 7 | Power_+ | White/Brown | White/Brown |
Pin 8 | Power_+ | Brown | Brown |
_
Transmission Distance | Transmission Voltage (Voltage Drop) | ||
---|---|---|---|
12VDC/0.5A camera_requirement | 12VDC/1A camera_requirement | 12VDC/1.5A camera_requirement | |
50m / 160ft | 13.5V (1.5V) | 15.5V (3.5V) | 17.0V (5.0V) |
100m / 320ft | 15.5V (3.5V) | 18.5V (6.5V) | 22.0V |
RETURNS POLICY
To return goods we have delivered to you, please contact us within 30 days from the date you have received the item. A staff member will then assist you with any return or repair. This may include inspecting the goods, arranging for the goods to be sent for repair, or providing you with a replacement.
Incorrectly Ordered/Change Of Mind:
Refunds are not normally provided where you have simply changed your mind or found the goods cheaper elsewhere. However, if goods have been incorrectly ordered, at our discretion, customers may be credited less a restocking fee.
A change of mind return will only be accepted if:
Please note: For change of mind returns, the shipping cost and method is the customer's responsibility. We will not compensate any returns that are lost or damaged in transit to us. For some change of mind returns, a restocking fee may apply.
Faulty Items
We recommend you immediately inspect any goods that we deliver to you or that you collect from our store to ensure you are completely satisfied with the goods. If any goods arrive damaged, please contact us as soon as possible. We will arrange to have the damaged goods returned and either arrange for a replacement of the goods or refund. Replacements and refunds of new products that are damaged on delivery or faulty from new requires a proof of purchase of the product and be returned with all original packaging, accessories and/or manuals included. Refunds will be made via the method of payment you used to make your purchase. If we consider the goods to have breached a consumer guarantee, any shipping costs to return the goods to us will be at our cost and compensated.
Repairs
The product must be returned with proof of purchase, it must not be modified or mistreated in any way and it must not have been serviced elsewhere. Goods returned for repair will be assessed and/or repaired within a reasonable time. You may be required to pay labour, assessment and/or freight fees, such as where goods are assessed to have been damaged by misuse or accident. We may provide you with an approximate fee; this may vary due to reasons beyond our control. In some circumstances, goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods.