The Cable Prowler combines the functions ofa high-end cable tester and length measurement tester, with the capability to identify link status, link capability, andPoE detection. All of this is in full color and internal memory to save results.
The Cable Prowler provides full cable testing on any category network, coax, or telephone cable. It will display wire map, numbered ID remotes, and any faults, including shorts, opens, miswires, split pairs, and reverses. The full-featured Cable Prowler measures cable length (using TDRtechnology) and generates tone levels for signal tracing andcable identification on all pairs, a selected pair, or a selected pin. All of this is displayed in a full color graphical display for easy viewing in any environment. CableProwler also has the ability to name each cable and save alltest results. Cable results can be exported to a computer via micro USB cable for record keeping and printing.
The Cable Prowler enables quick identification of a network drops link capability and current link status. CableProwler also detects the presence of PoE on the network dropand what class of PoE per IEEE 802.3 af/at with load test for voltage drop. These network tests can also be saved for record keeping and printing.
Measurement Technology | Time Domain Reflectometry (TDR) |
Cable Measurements | Cable Testing and ID: up to 305 m Split Pair Detection: 1 m to 305 m Length Measurement: 0 to 457 m, ± 5% Supports 8 continuity and ID number remotes (RJ-45) Supports 20 RJ-45 and 20 F-connector ID only remotes |
Power over Ethernet | Tests for IEEE 802.3af and IEEE 802.3at (PoE Plus)compliant PoE Tests for classes and loads cable up to 25.5 watts (at class 4) Identifies Mode A or B (pairs with PoE) |
Active Ethernet | Indicates advertised speeds of 10/100/1000base-t half or full duplex Can Link to network at 10/100base-t |
Maximum Voltage | Parameters refer to the maximum voltage that can be applied to any 2 connector pins without causing damage tothe tester. −RJ Jack: 66 Vdc or 55 Vac −F-connector: 50 Vdc or Vac |
Save Test Results | Stores up to 250 Cable or network tests with user defined names |
Tone Generation | Tone Frequencies: 730 Hz and 1440 Hz |
Languages | English, French, Spanish, German, Italian |
Battery Life | For 6 x AA, 9VDC, 2,200 mA-hr (typical) alkaline battery: Operating ? 20 hours typical Standby ? 1.5 years typical (200uA max standby current) Batteries are included |
Altitude | 3048 m operating |
Temperature | Operating: 0 to 50°C Storage: -30 to 60°C |
Humidity | 10 to 90% non-condensing |
Enclosure | High-strength PC/ ABS plastic with V0 rating with boot Withstands 4 foot drop on to concrete |
Size | 4.7 x 9.15 x 17.3 cm |
Weight | With batteries: 510 g |
Safety Compliances | CE |
Warranty | 1 Year |
Q. What is VoP?
A. The Cable Prowler uses Time Domain Reflectometry to measure cable length and the distance to faults. VoP is the signal percentage compared to the speed of light. To calibrate the VoP, please refer to page 13 of Cable Prowler instruction manual.
Q. What does "Split" mean?
A. A cable can be wired with correct continuity but not withcorrect pairing. This most often happens when the cable is terminated consistently at both ends, but in the wrong order. The Cable Prowle will display "Split" next to the pair(s) that are not paired correctly.
Q. What is an "Open"?
A. Cable Pair(s) do not have continuity throughout the cableor the Cable Prowler? remote is not detected. An open condition will be displayed in the wire map diagram.
Q. What is a "Short"?
A. Cable Pair(s) are making an electrical connection with each other or foreign object.
Q. Why are the lengths different for each pair?
A. Due to the varying twists of each pair, their length will differ.
Q. What's the difference between the remotes?
A. The Network Telephone test remotes (black remotes with the white label) are used for performing a cable test and providing an ID. The small yellow remotes will provide an IDonly. You can also use the coax remotes to perform a test and obtain an ID for coax cables.
Q. Why doesn't the Cable Prowler show PoE Results?
A. Make sure the PoE test is on. If the "PoE Off" soft key icon is displayed, press the soft key below it to activate the PoE test. If PoE results are not displayed with when thePoE test is on, check your switch to verify that PoE is enabled.
Q. What does Link Flow Control mean?
A. Link Flow control is a switch configuration feature that pauses data transmission when there is system congestion. The Cable Prowler? identifies if this feature is enabled on the switch.
Q. What are FDX and HDX?
A. FDX is an acronym for Full duplex. HDX is an acronym for Half Duplex.
Q. Why doesn't the Application detect my Cable Prowler?
A. Make sure your Cable Prowler? is powered on and plugged into your computer using a micro USB cable. While plugged in to your PC, turn the Cable Prowler off then back on.
Q. There was an error when I attempted to update the Firmware
A. If the Cable Prowler is still on, click on "Begin Download" on the application again.
Q. My Cable Prowler won't turn on after I updatedthe Firmware.
A. An error occurred during the Firmware installation but don't worry, it's still in boot loader mode (program mode). Unplug the Cable Prowler, close the application, then plug the Cable Prowler back in to your PC. Open the application and follow the Firmware update instructions. The Cable Prowler? screen will remain dark until it has been successfully updated.
Q. How do you test an Ethernet cable via Ethernet wall plate/server/router ports?
A. The 12inch Ethernet Patch Cable (CA016) allows you to connect to an RJ45 plug to test a shielded or non-shielded Ethernet cable.
Q. How do I test unterminated Ethernet cables?
A. The 8-way Alligator Clip Cord Set (CA015) allows you to test unterminated Ethernet cable. This unique cord set has an RJ45 plug on one end and an alligator clip connected to each wire on the other end. This accessory allows you to make sure cables have not been damaged
Aussie Stock
All our stock is kept in our Melbourne based warehouse. Our stock levels are also updated every 10 minutes! So if it says 10 units in stock, you can trust that it is accurate.
No PO Boxes or Parcel Lockers
At this stage we only use couriers and can only deliver to a road-side address. This means PO Boxes and Parcel Lockers cannot be accepted as StarTrack do not deliver to these addresses.
In instances where a PO Box or Parcel Locker address in entered, we may ask for an alternative road-side address, or cancel and refund your order immediately and urge you to replace your order with an alternative delivery address.
Delivery times
We typically dispatch our goods same day or next day. From there, you can expect 2 - 8 business days Australia wide. Most capital cities can expect 1-2 day delivery times.
Any RTS (Return to Sender) orders due to missing or incorrect address information entered by the buyer may incur an additional charge for redelivery.
RETURNS POLICY
To return goods we have delivered to you, please contact us within 30 days from the date you have received the item. A staff member will then assist you with any return or repair. This may include inspecting the goods, arranging for the goods to be sent for repair, or providing you with a replacement.
Incorrectly Ordered/Change Of Mind:
Refunds are not normally provided where you have simply changed your mind or found the goods cheaper elsewhere. However, if goods have been incorrectly ordered, at our discretion, customers may be credited less a restocking fee.
A change of mind return will only be accepted if:
Please note: For change of mind returns, the shipping cost and method is the customer's responsibility. We will not compensate any returns that are lost or damaged in transit to us. For some change of mind returns, a restocking fee may apply.
Faulty Items
We recommend you immediately inspect any goods that we deliver to you or that you collect from our store to ensure you are completely satisfied with the goods. If any goods arrive damaged, please contact us as soon as possible. We will arrange to have the damaged goods returned and either arrange for a replacement of the goods or refund. Replacements and refunds of new products that are damaged on delivery or faulty from new requires a proof of purchase of the product and be returned with all original packaging, accessories and/or manuals included. Refunds will be made via the method of payment you used to make your purchase. If we consider the goods to have breached a consumer guarantee, any shipping costs to return the goods to us will be at our cost and compensated.
Repairs
The product must be returned with proof of purchase, it must not be modified or mistreated in any way and it must not have been serviced elsewhere. Goods returned for repair will be assessed and/or repaired within a reasonable time. You may be required to pay labour, assessment and/or freight fees, such as where goods are assessed to have been damaged by misuse or accident. We may provide you with an approximate fee; this may vary due to reasons beyond our control. In some circumstances, goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods.