NP800KIT PLATINUM TOOLS Net Prowler Network Tester Advanced Cabling Tester Supports Ipv4 and Ipv6
The Net Prowler Cabling and Advanced Network Tester takes all the features and functionality of the Cable Prowler and adds the capability to identify, monitor, and troubleshoot LAN issues associated with physical layer and link conditions in the network.
Platinum Tools Innovation Blog Comparison :
| Measurement Technology | Time Domain Reflectometry (TDR) |
| Cable Measurements | Cable Testing and ID: up to 305 m Split Pair Detection: 1 m to 305 m Length Measurement: 0 to 457 m, ±5% Supports 8 continuity and ID number remotes (RJ-45) Supports 20 RJ-45 and 20 F-connector ID only remotes |
| Power over Ethernet | Tests for IEEE 802.3af and IEEE 802.3at (PoE Plus)compliant PoE Tests for classes and loads cable up to 25.5 watts (at class 4) Identifies Mode A or B (pairs with PoE) |
| Active Ethernet | Indicates advertised speeds of 10/100/1000base-t half or full duplex Can Link to network at 10/100base-t |
| Maximum Voltage | Parameters refer to the maximum voltage that can be applied to any 2 connector pins without causing damage tothe tester. |
| Save Test Results | Stores up to 250 Cable or network tests with user defined names |
| Tone Generation | Tone Frequencies: 730 Hz and 1440 Hz |
| Languages | English, French, Spanish, German, Italian |
| Battery Life | For 6 x AA, 9VDC, 2,200 mA-hr (typical) alkaline battery: Operating: 20 hours typical Standby: Life of battery (20uA max) Batteries are included |
| Altitude | 3048 m operating |
| Temperature | Operating: 0 to 50°C Storage: -30 to 60°C |
| Humidity | 10 to 90% non-condensing |
| Enclosure | High-strength PC/ABS plastic with V0 rating with boot Withstands 4 foot drop on to concrete |
| Size | 4.7 x 9.15 x 17.3 cm |
| Weight | With batteries: 510 g |
| Safety Compliances | CE |
| Warranty | 1 Year |
Q. Why does the Net Prowler only display part of the Network/PoE test results?
A. The Net Prowler first checks for voltage upon entering the PoE/Network screen so if PoE is not present, the port and Net Prowler timing may be conflicting. The solution is to turn off the PoE test by pressing the PoE Off soft key then press the test button again.
Q. Why don't I get any results when I do a CDP test?
A. The network does not have a Cisco switch or device. The Cisco device may not be configured to display CDP
Q. Why don't I get any results for LLDP?
A. The switch you are connected to does not broadcast Link Layer Discovery Protocol information.
Q. Why isn't my Net Prowler showing any results?
A. If the "Testing" light is illuminated, the Net Prowler has not completed the test. If the light turns off without providing results, check that your cable is connected to the network or disconnect and test the cable in the cable test menu.
Q. Why does the Net Prowler perform a DHCP test when I enter the Network Mapping menu?
A. The Net Prowler joins a network by obtaining an IP address via DHCP. This allows the Net Prowler to ping and perform additional network tests.
Q. Why does the Net Prowler only display the IP Ientered when I ping an IP?
A. The Net Prowler did not get a response from the target device.
Q. What's the difference between the remotes?
A. The Network Telephone test remotes (black remotes with the white label) are used for performinga cable test and providing an ID. The small yellow remotes will provide an ID only. You can also use the coax remotes to perform a test and obtain an ID for coax cables.
Q. What does "Split" mean?
A. A Split error is displayed when pairshave been improperly terminated at both ends.
Q. Why do I get an error when I try to install firmware to the Net Prowler using the application?
A. The Net Prowler bootloader needs to be initiated. If this is unsuccessful, another attempt will need to be made. Click "OK" then click on begin download again. Also, make sure the Net Prowler is on and has sufficient battery charge.
Q. Neither the Control or Throughput tests are working.
A. Make sure the Net Prowler is connected to the same subnet as the computer you are using. Check to make sure the application has the same Tester IP asthe Net Prowler. This can be identified in the DHCP test screen or the TCP/UDP screen.
Q. How do you test an Ethernet cable via Ethernetwall plate/server/router ports?
A. The 12inch Ethernet Patch Cable (CA016) allows you to connect to an RJ45 plug to test a shielded or non-shielded Ethernet cable.
Q. How do I test unterminated Ethernet cables?
A. The 8-way Alligator Clip Cord Set (CA015) allows you to test unterminated Ethernet cable. Thisunique cord set has an RJ45 plug on one end and an alligatorclip connected to each wire on the other end. This accessoryallows you to make sure cables have not been damaged before you spend the time and money to terminate them.
Q. How do I extend the life of my RJ45 Jack?
A. The Sacrificial RJ45 Cable (CA014) extends the life of the RJ45 jacks on your tester and remote(s). Plug the sacrificial cable into the tester or remote and then plug the cables to be tested into the sacrificial cables. Continue testing cables with the sacrificial cables plugged into the tester or remote(s). If the sacrificial cables become worn or damaged, simply replace them. This prevents downtime and saves money by not having to send your tester in for an RJ45 jack replacement.
Q. How do I test cables with BNC connectors?
A. The F-jack to BNC jack allows you to easily test coax cables that have been terminated with BNC connectors.
RETURNS POLICY
To return goods we have delivered to you, please contact us within 30 days from the date you have received the item. A staff member will then assist you with any return or repair. This may include inspecting the goods, arranging for the goods to be sent for repair, or providing you with a replacement.
Incorrectly Ordered/Change Of Mind:
Refunds are not normally provided where you have simply changed your mind or found the goods cheaper elsewhere. However, if goods have been incorrectly ordered, at our discretion, customers may be credited less a restocking fee.
A change of mind return will only be accepted if:
Please note: For change of mind returns, the shipping cost and method is the customer's responsibility. We will not compensate any returns that are lost or damaged in transit to us. For some change of mind returns, a restocking fee may apply.
Faulty Items
We recommend you immediately inspect any goods that we deliver to you or that you collect from our store to ensure you are completely satisfied with the goods. If any goods arrive damaged, please contact us as soon as possible. We will arrange to have the damaged goods returned and either arrange for a replacement of the goods or refund. Replacements and refunds of new products that are damaged on delivery or faulty from new requires a proof of purchase of the product and be returned with all original packaging, accessories and/or manuals included. Refunds will be made via the method of payment you used to make your purchase. If we consider the goods to have breached a consumer guarantee, any shipping costs to return the goods to us will be at our cost and compensated.
Repairs
The product must be returned with proof of purchase, it must not be modified or mistreated in any way and it must not have been serviced elsewhere. Goods returned for repair will be assessed and/or repaired within a reasonable time. You may be required to pay labour, assessment and/or freight fees, such as where goods are assessed to have been damaged by misuse or accident. We may provide you with an approximate fee; this may vary due to reasons beyond our control. In some circumstances, goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods.
Copyright 2024 MyDeal.com.au - © All rights reserved