This Hobbes PoEz kit comes with PoEz power over Ethernet detector and PoEz PDS powered device simulator.
PoEzis a Power Over Ethernet Detector/PoE Tester that can be used for PSE (power source equipment), power supply status detection during PoE system or CCTV system installation. It can distinguished whether the PSE power supply by Active mode under the IEEE 802.3AF/AT/UPoE/BT standard or by non-standard Passive mode. With the supplied PoEz PDS (powered device simulator), it can monitor the current PSE power supply status after connecting the other end to the simulator. PoEz is designed with an OLED high resolution display for user to view the receiving voltage, current and power of PD. It is also able to distinguished the circuit polarity of PoE during PoE system installation or troubleshooting.
• New battery-free operation technology
• Monitor and troubleshoot the IEEE 802.3AF / 802.3AT(PoE+) / UPoE / 802.3BT Type 3(4PPoE) and 802.3BT Type 4 standard PoE system with Hobbes PoEz PDS 256318/PDS
• Compact and lightweight design
• Monitoring the current PoE status with an easy to read high resolution OLED display
• Compatible with new IEEE 802.3BT Type 4 standard
Real-time monitoring the receiving voltage, current and power of PoEz PDS or PD by PoEz
Distinguished PSE status by PoEz
Long term PoE monitoring by PoEz
_
Connectors:
PoEz: Two RJ45 jacks for line in/line out
PDS: One RJ45 jack for line in
Detection resolution:
PoEz Voltage: 1V; Current: 0.01A; Power: 1W
PDS: N/A
Measurement accuracy:
PoEz Power: ±1W
PDS: N/A
Maximum detected power:
PoEz: 160W (Mode A 80W, Mode B 80W)
PDS: 6W (Mode A 3W, Mode B 3W)
Dimension:
PoEz: 32mm x 86mm x 22mm
PDS 30.3mm x 44.26mm x 35.82mm
Weight:
PoEz: 45g
PDS 30.2g
Power source: No
1. Why do I need PoEz Power Over Ethernet Detector/PoE Tester?
Power over Ethernet (PoE) IEEE802.3bt standard was officially released in September 2018. Prior to the launch of this standard, global PoE chips and manufacturers have Hi-PoE and UPoE products for high-power applications. Prior to IEEE802.3bt, the IEEE 802.3af and IEEE 802.3at standards have existed for many years. Today, this technology had developed and continues to grow in today's infrastructures. As a result, some manufacturers have introduced PoE switches, PoE injectors, PoE Cameras that aredesigned to save cost and special applications for this technology. As with any growing technology, connection and compatibility problems between devices makes the installation and maintenance of the PoE system complicated and difficult to manage.
With Hobbes PoEz - Power Over Ethernet Detector/PoE Tester, it allows engineers to determine whether the PSE transmits signal (via handshake), PoE supply voltage, current, power draw for IEEE 802.3af / 802.3at (PoE+)/ UPoE / 802.3bt of Type 3 (4PPoE) and 802.3bt Type 4 to ensurethatall network devices are connected.
2. What is PoEz Power Over Ethernet Detector/PoE Tester?
PoEz Power Over Ethernet Detector/PoE Tester supports thelatest IEEE 802.3bt standard. It can quickly identify the operating status of the PoE system. It was designed by battery-free technology. It is the latest PoE test tool design developed specifically for engineers and installers during PoE system installation such as CCTV/PoE cameras, VOIP phones, Wi-Fi installations, POS Systems and much more.PoEz supports 4 pairs from a power supply that delivers power over to all 4 Pairs with a maximum measurement of power up to 160W (Mode A 80W, Mode B 80W). It has a high-resolution OLED screen to clearly display the voltage, current, power data results. The other LED can quickly identify whether the PSE transmits via handshake signals to the PD (Powered Device).
PoEz is easy to use and read. With Hobbes PoEz PDS accessory, it simulates a PD to identify the issues on devices.
3. How to use PoEz when PoE polarity is 12-, 36 +, 45 + and 78 - on IEEE 802.3bt PSE?
In rare cases, the current and power of Mode A (12, 36) are zero; Mode B (45, 78) have a value or the current and power of Mode A (12, 36) have value; Mode B (45, 78) is zero, which indicates that the polarity of PSE is designed to be a rare combination of 12-, 36+, 45+, 78-. In this instance, it is necessary to switch the direction of PSE andPD connections to obtain the values of both Mode A and B.
4. I finish the PoE voltage, current and power draw test on PoE injector and wifi access point by PoEz Power Over Ethernet Detector/PoE Tester. Then switch the function from display to PSE Status and remove wifi access point. Why doesLED light turn on for a few seconds before it flashes?
The reason is that when the powered device is removed, some of the PoE Injector or PoE switch will not immediately stop supplying power, which will cause the PoEz to still detect the PoE power and keep the LED on. Once the PoE Injector or PoE switch stops supplying power, the PoEz LED immediately switches to flash.
5. When using the PoEz Power Over Ethernet Detector/PoE Tester to connect the PoE switch and the PoE camera to perform PoE long-term monitoring and switch to PSE Status, the LED is on, indicating that the PoE switch is powered on.But why does the PoEz screen show no information of voltage,current and power when switching the toggle to Display?
This can occur on some PoE switches. Mainly due to the PoEz - Power Over Ethernet Detector/PoE Tester needs reaction time. Wait a few seconds to display the value.
Weight: 0.1800
Aussie Stock
All our stock is kept in our Melbourne based warehouse. Our stock levels are also updated every 10 minutes! So if it says 10 units in stock, you can trust that it is accurate.
No PO Boxes or Parcel Lockers
At this stage we only use couriers and can only deliver to a road-side address. This means PO Boxes and Parcel Lockers cannot be accepted as StarTrack do not deliver to these addresses.
In instances where a PO Box or Parcel Locker address in entered, we may ask for an alternative road-side address, or cancel and refund your order immediately and urge you to replace your order with an alternative delivery address.
Delivery times
We typically dispatch our goods same day or next day. From there, you can expect 2 - 8 business days Australia wide. Most capital cities can expect 1-2 day delivery times.
Any RTS (Return to Sender) orders due to missing or incorrect address information entered by the buyer may incur an additional charge for redelivery.
RETURNS POLICY
To return goods we have delivered to you, please contact us within 30 days from the date you have received the item. A staff member will then assist you with any return or repair. This may include inspecting the goods, arranging for the goods to be sent for repair, or providing you with a replacement.
Incorrectly Ordered/Change Of Mind:
Refunds are not normally provided where you have simply changed your mind or found the goods cheaper elsewhere. However, if goods have been incorrectly ordered, at our discretion, customers may be credited less a restocking fee.
A change of mind return will only be accepted if:
Please note: For change of mind returns, the shipping cost and method is the customer's responsibility. We will not compensate any returns that are lost or damaged in transit to us. For some change of mind returns, a restocking fee may apply.
Faulty Items
We recommend you immediately inspect any goods that we deliver to you or that you collect from our store to ensure you are completely satisfied with the goods. If any goods arrive damaged, please contact us as soon as possible. We will arrange to have the damaged goods returned and either arrange for a replacement of the goods or refund. Replacements and refunds of new products that are damaged on delivery or faulty from new requires a proof of purchase of the product and be returned with all original packaging, accessories and/or manuals included. Refunds will be made via the method of payment you used to make your purchase. If we consider the goods to have breached a consumer guarantee, any shipping costs to return the goods to us will be at our cost and compensated.
Repairs
The product must be returned with proof of purchase, it must not be modified or mistreated in any way and it must not have been serviced elsewhere. Goods returned for repair will be assessed and/or repaired within a reasonable time. You may be required to pay labour, assessment and/or freight fees, such as where goods are assessed to have been damaged by misuse or accident. We may provide you with an approximate fee; this may vary due to reasons beyond our control. In some circumstances, goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods.