AMP-235 is designed in 2 channel Class D amplifier, with the design of space saving. It is the best solution for customer who need a simple design. It is very easy to mount behind the flat TV and pr ovide the better sound. The build-in IR learning function allows the volume to be controlled by TV's remote control, or even other IR control kit. AMP-235 is an ideal amplifier for your home entertainment System.

The AMP-235 sits at the back of your TV and powers speakers and potentially a sub which is great for movies. Your current TV remote can be used to operate the AMP-235.

• Audio Inputs: Stereo Line Level, coaxial or optical (PCM format)
• Outputs: 35W /Channel, 1kHz into 4 Ohms
• Speaker out - removable screw-down connector for up to14AWG wire
• Subwoofer out - (RCA) with integrated 120Hz low pass filter
• IR Sensor Input: 3.5mm stereo jack
• Amplifier Channels: 2 Signal-to-Noise Ratio: 90dB (1KHZ) Frequency Response: 20Hz to 20kHz +3dB
• Input Impedance: 47K Power
• Requirements: 24VDC 3.75A (External power supply)
• Dimensions (WxDxH): 6" x 8" x 1.2" (154 x 203 x 30 mm)

Q: What is the remote control for?

A: The remote control is default to control the volume of the amplifier AMP235. AMP235 can also learn three IR commands (Vol+, Vol-, and Mute) from your TV or Foxtel remote control. After it learns, you can use your TV/Foxtel remote control to controlthe volume of the amplifier. However, the supplied AMP235 remote control will not work anymore._

Q: What are the steps to learn IR commands from the TV (Vol+, Vol-, and Mute), refer to the video._

A: The Vol+, Vol- and Mute commands must be learned in sequence, 1st Vol+, then Vol-, then Mute.

1. _On AMP235, press and hold the IR Learning Button for 2 seconds until the IR Confirm LED blinks slowly._
2. Place your TV remote control about 3-4 inches (7-10cm) away from the IR Learning window of AMP235, aiming the remote directly at theIR Learning window._
3. Press and hold the TV remote's Vol + key until the IR Confirm LED blinks for 1 second._
4. Press and hold the TV remote's Vol - key until the IR Confirm LED blinks for 1 second._
5. Press and hold the TV remote's Mute- key until the IR Confirm LED blinks for 1 second._
6. Confirm proper operation of all three volume commands. If any of the three commands must be re-learned, all three commands must be re-learned in order.__
   

Q: I plug in the powersupply, but the power LED light is not ON._

A: The power LED maybehave been disabled, you can enable it by pressing and hold the AMP235 IRLearning Button for approximately 10 seconds while powering Confirm LED will blink once when togging from "Disabled" to Enabled" and twice when toggling from "Enabled" to "Disabled". Once the IR Confirm LED has blinked, you can release the IR Learning Button._

Weight: 1.534

Aussie Stock
All our stock is kept in our Melbourne based warehouse. Our stock levels are also updated every 10 minutes! So if it says 10 units in stock, you can trust that it is accurate.

No PO Boxes or Parcel Lockers
At this stage we only use couriers and can only deliver to a road-side address. This means PO Boxes and Parcel Lockers cannot be accepted as StarTrack do not deliver to these addresses.
In instances where a PO Box or Parcel Locker address in entered, we may ask for an alternative road-side address, or cancel and refund your order immediately and urge you to replace your order with an alternative delivery address.

Delivery times
We typically dispatch our goods same day or next day. From there, you can expect 2 - 8 business days Australia wide. Most capital cities can expect 1-2 day delivery times.
Any RTS (Return to Sender) orders due to missing or incorrect address information entered by the buyer may incur an additional charge for redelivery.