RUSTOLEUM CONCRETE SAVER 5600 System Acrylic Urethane Floor Paint (WHITE)

ABOUT 5600 SYSTEM ACRYLIC URETHANE FLOOR PAINT

Get quick color and protection with Rust-Oleum Concrete Saver 5600 System Acrylic Urethane Floor Paint. This convenient, high-gloss, water-based coating is ideal for use in mild industrial or commercial settings. Great for floors, walkways, decks, etc.

• Protects concrete floors from dusting, water damage, staining and mildew
• Paint and go-no measuring or mixing; minimal surface prep
• Excellent coverage over new and previously coated surfaces; for interior/exterior use
• Dries fast-accepts next-day foot traffic; easy brush, spray or roller application
• Low odor, soap-and-water clean-up, VOC-compliant nationwide
• Meets USDA requirements for incidental food contact; accepted for use in federally registered Canadian food facilities
• Withstands repeated heavy abrasion, including mechanical wear and tear and repeated scrubbing with industrial solvents, cleaners, and scouring agents

For Best Results

• Use 200 Anti-Skid Floor Coating Additive where oil or water spills may occur.

1Dry film thickness

For Best Results

• Mix contents with a mechanical mixer. Apply using a phenolic core roller

SURFACE PREPARATION

New concrete should be allowed to cure for 30 days before application of any coating. If there is any doubt about the dryness of the concrete, conduct a test by simply taping a piece of 4 mil plastic sheet 18" by 18" on the bare concrete for 24 hours. Be sure to tape all four sides. After 24 hours, check the concrete for signs of moisture. The concrete will be darker if damp. If moisture is found, allow additional drying time (10-14 days) and repeat test. If repeated tests continue to indicate the presence of moisture, contact Rust-Oleum Technical Service for assistance. Check for curing compound or other types of sealers by pouring a small amount of water onto the concrete. If water soaks in, the surface is suitable for coating. If water beads up on the concrete, the surface is not porous and a test application is warranted to ensure proper adhesion will develop. Sanding or mechanical abrading may be required if proper adhesion does not develop. Contact Rust-Oleum Technical Service for detailed information.

Remove all grease, oil, dirt, and other contaminants by cleaning with Krud Kutter(R) Cleaner Degreaser, detergent or other suitable cleaner and rinse with fresh water. This is best accomplished using a standard floor scrubber/polisher with a heavy duty stripping pad (such as 3M 7300 or similar). A thorough rinse must be done if the concrete has been acid stained or if the concrete had been acid etched.

The floor should be dry and dust free prior to application. Vacuum to remove fine dust and debris.

SURFACE PREPARATION (cont.)

Previously coated floors need to be in good sound condition with proper adhesion to the concrete substrate. Check the adhesion of the previous coating by cutting a small X in the coating using a sharp razor knife, firmly apply a piece of 2" duct tape over the center of the X cut, then pull off with a fast snap. The coating is suitable to topcoat if no significant previous coating is removed beyond the X cut. If the coating fails this test, then additional surface preparation is required. Contact Rust-Oleum Technical Service for assistance.

APPLICATION

Apply only when air, surface, and material temperatures are between 50-90oF (10-32oC), surface is at least 5oF above the dew point and relative humidity is below 85% during and after application. Apply by roller using a good quality 3/8" synthetic nap cover. Avoid applying excessive material. Do not allow the coating to puddle. The coating should be applied within the published coverage rate of 170-270 sq. ft. per gallon. On new or uncoated concrete, two coats of product should be applied. Do not thin. Allow coated floor to cure 7 days before mopping or washing. Use Rust-Oleum 200 Anti-Skid Floor Coating Additive for skid resistance where oil or water spillage is a problem.

CLEAN-UP

Soap and water. Once coating begins to cure, 160 Thinner or MEK may be required.

Available Size

• 3.78litre