36 Pin Replacement Cartridges for A9W PowerDerm 10X

Take exceptional care of vital areas of your skin, including the face, neck, neckline, stomach, thighs, buttocks, and scalp, by incorporating the 36-Pin Microneedle Cartridges into your skincare routine. Designed for use with the Dr. Pen A9 Microneedling Pen, this cartridge of choice is adept at addressing a wide range of skin concerns.

The 36-Pin Microneedle Cartridges are specifically tailored to target various body area skin issues, such as:

1. Acne scarring and other body scarring
2. Surgical scars
3. Stretch marks
4. Body skin texture
5. Hair loss

Benefit from the full potential of the 36-Pin Microneedle Cartridges when paired with the Dr. Pen A9 Microneedling Pen, effectively addressing skin issues that matter to you.

Additionally, the 36-Pin Microneedle Cartridges boast several key features to enhance their functionality:

1. The surface is equipped with a wavy contact for improved absorption of skincare products.
2. A three-snap fixed structure provides added protection for the device machine.
3. They can be easily connected with the Dr. Pen A9 microneedling pen.
4. The gauge is made from high-quality stainless steel, ensuring durability.
5. With a maximum depth of 2.5mm, they can effectively address various skin concerns.

What's Included

• 10x pack of 36-pin Microneedle Cartridges for Dr. Pen A9 Microneedling Pen

Important

• DO NOT USE one cartridge more than once for safety and hygiene reasons
• DO NOT USE in open wounds
• DO NOT USE on acne
• DO NOT USE or continue to use if irritation happens
• Microneedling cartridges must be sterilised before each use to ensure the treatment is safe and hygienic. It is essential to follow these steps carefully to ensure that the microneedling cartridges are properly sterilised. Here are the steps to sterilise microneedling cartridges:

1. First, ensure that you have all the necessary equipment for sterilisation; gloves, isopropyl alcohol solution (70% or above) and a clean container to hold the solution.
2. Put on your gloves to avoid contaminating the cartridges during the sterilisation process.
3. Check on your cartridge; ensure the needles are in perfect condition (i.e. not bending) and remove any debris.
4. Pour enough alcohol solution into the container and dip the cartridge needle into a sterilisation container, then soak for a couple of minutes.
5. If you have alcohol solution in a spray model, you can spray it towards the needle head of the cartridge.
6. Once the sterilisation is complete, allow the cartridge to air dry before using it.
7. Finally, your cartridge is ready for use.

How to Use

1. To ensure there is no cross-contamination, cartridges must be sterilised before treatment.
2. Remove the cover on the top of the cartridge
3. Put together the cartridge to the Dr. Pen A9 Microneedling Pen
4. After double-cleansing the face and body area of treatment, dry it with a towel
5. Configure depth and speed according to your preferred treatment
6. Turn the pen on, then slowly start the treatment in small areas
7. Recommended to use Femvy Hyaluronic Acid to boost results
8. Recommended to use is a cross-hatch pattern
9. Only use light pressure and ensure not to drag or pull the skin

Usage

• Microneedling should be performed once every 4-6 weeks
• Safely dispose of your microneedling cartridge after one treatment

Disclaimer

Please speak with your doctor before purchasing any Dr Pen products. The content on this site is not intended to substitute for the advice of a qualified physician, pharmacist, or other licensed healthcare professional. The products may have additional information and instructions on or inside the packaging that you should carefully read and follow. Contact your healthcare provider immediately if you suspect that you have a medical problem. This product may not have been evaluated by the Food and Drug Administration and is not intended to diagnose, treat, cure, or prevent any disease or health condition. For any concerns or questions, please contact your GP or dermatologist.