PROCESSOR & STORAGE | - Powerful 720Mhz ARM Cortex A8 processor with 128Mbyte DDR2 RAM
- 256MByte Flash memory storage (~120MB available on board space for user storage)
- MicroSD card slot for additional storage
|
OPERATING SYSTEM | - Embedded Linux & Software Development Kit (SDK)
|
CELLULAR BANDS | - LTE:
- – Band 1 (2100 MHz)
- – Band 3 (1800 MHz)
- – Band 7 (2600 MHz)
- – Band 8 (900 MHz)
- – Band 20 (800 MHz)
- UMTS/HSDPA/HSUPA/HSPA+/DC-HSPA+:
- – Band 1 (2100 MHz)
- – Band 2 (1900 MHz)
- – Band 5 (850 MHz)
- – Band 8 (900 MHz)
- GSM/GPRS/EDGE:
- – GSM 850 (850 MHz)
- – EGSM 900 (900 MHz)
- – DCS 1800 (1800 MHz)
- – PCS 1900 (1900 MHz)
|
PEAK DATA SPEED | - LTE: Category 3:
- – 100 Mbps / 50 Mbps (Downlink/Uplink) (20Mhz bandwidth)
- – 50 Mbps / 25 Mbps (Downlink/Uplink) (10Mhz bandwidth)
- HSPA+:
- – 42 Mbps downlink (Category 24)
- – 5.76 Mbps uplink (Category 6)
- EDGE
- – 236 kbps throughput
|
CONNECTIVITY | - 2 x 10/100/1000 Base-T Ethernet RJ45 ports with Auto MDIX
- Micro USB 2.0 OTG interface with 0.5A supply capability
- 1 x multipurpose I/O pin
|
SIM CARD READER | - Lockable Tray Reader with Push-Button-to-Release
- – optional soldered-down SIM (ETSI MFF2 DFN-8 USIM)
- Supports Mini USIM/SIM Format (2FF)
|
RESET BUTTON | - Reset button (recessed, requiring pen/paperclip) with three functions: Reboot, reboot into recovery mode, and reset unit to factory defaults
|
ANTENNA CONNECTORS | - 2x SMA connectors for 3G/4G
- 1x SMA connector for GPS
|
LED INDICATORS | - Tri-colour (Red/Amber/Green) LEDs. Power, Mobile Broadband, Service Type and Signal Strength indicators
- Easy and clear LED status display for connection status, connected network type, and connection errors
|
CELLULAR | - Profile managed packet data connections NAT Disable for framed route configuration Transparent bridge mode using PPPoE to allow the router to transparently forward Public WAN IP address to a downstream device
- SIM Security Management (PIN configuration, enable
- and disable)
- Automatic and manual cellular band selection
- Automatic and manual operator selection
|
GPS | - Embedded GPS receiver (1575.42Mhz)
- SMA Connector for external passive or active GPS Antenna
- Active antenna voltage: 3.05V
- Maximum current: 50mA
- Tracking sensitivity under open sky: -161dBm
- Acquisition sensitivity under open sky: -145dBm
- Cold start sensitivity: -145dBm
- Time to first fix (TTFF): Cold 32s, Warm 29s, Hot 1s
|
NETWORK & ROUTING | - Static Routing, RIP (v1/v2), Port Forwarding and DMZ
- Dynamic DNS
- VRRP for redundant router failover
- DHCP Server, including :
- – Address reservation by MAC address
- – Custom DNS server definitions
- – DHCP Relay
- – DHCP list display in Web-UI
- – Advanced DHCP Option configuration (Option 42 NTP, Option 66 TFTP, Option 150, Option 160)
- Data Stream Manager providing ability to create mappings between input and output ports (e.g. Serial Port, SMS, GPS, USB) and perform required translation or data processing by each virtual tunnel.
- Modbus Server TCP/IP Gateway and Client TCP/IP Agent with up to 247 slaves connected to the Serial TCP/IP Gateway.
- Modbus RTU/ASCII frames support.
|
VPN | - PPTP Client for VPN connectivity to remote PPTP VPN Server
- IPSec tunnel termination (for up to 5 tunnels)
- GRE Tunnelling
- OpenVPN (Client, Server and P2P)
|
ADMIN & CONFIGURATION | - Web-based User Interface (HTTP/HTTPS) for full device status and configuration
- Password protected configuration file backup and restore for quick device configuration and device cloning
- Telnet Command Line Interface for status monitoring, configuration and control
- SNMP v1/v2 including cellular specific MIB, config and firmware download
- TR-069 Client for remote device configuration, configuration backup and restore, and firmware upgrade
- SMS messaging (Send/Receive) including inbox, outbox
- Ping monitor watchdog (Reset connection on repeated ping failure)
- Diagnostic Log Viewer (remote and local)
- System Status and Security Logs
- NTP Server Support for network time sync of device’s system clock
- Device User Guide stored on the device and accessible via the Web-based User Interface (HTTP/HTTPS)
- Advanced Diagnostics and Control via SMS
- – Query status information – such as Signal Strength, WAN IP, Uptime, and many more
- – Configure device remotely via SMS – such as APN, authentication settings, and many more
- – Execute commands via SMS – such as reboot, reset to defaults, go offline, and many more
- – Secure SMS management using sender whitelisting and password management
- – SMS acknowledgement replies for queries and commands
|
FIRMWARE MANAGEMENT | - Firmware upgrade locally via LAN or remotely Over-The-Air (HTTP/ HTTPS, SNMP, TR-069)
- Multiple firmware image storage on device and dynamic install
- Triggered firmware upgrade via SMS (initiate download & install from HTTP/HTTPS)
|
DIMENSIONS, WEIGHT & MOUNTING | - Develop and install custom software applications
- Open Linux standard development environment
- Develop applications/scripting in standard ANSI C/Shell script and LUA
- Package manager built into Web-UI for Application installation/removal
- API (C, LUA and Shell libraries) to the unit’s internal Runtime Database to allow full status monitoring configuration and control of the device from custom applications
|
TEMPERATURE | - Module Manufacturer’s Recommended Operating
- Temperature: -40ºC to +85ºC
- Storage Temperature: -40ºC to +85ºC
|
POWER SUPPLY | - AC Power supply available as an optional accessory
- Power input and I/O via 4 way Molex mini-fit connector
- DC Power (8 - 40V DC)
- 1x dedicated ignition input on 4 way connector
- Minimum power input rating of 6W via 4 way mini-fit connector. Recommended power input 12V 1.5A.
- Vehicle compatible protection on DC Input Jack. (ISO7637 standard)
|
CERTIFICATIONS | - CE (Europe)
- RCM (Australia)
- RoHS
- WEEE
|